Random notes: Difference between revisions

From flashrom
Jump to navigation Jump to search
(Writing or reusing a probe function)
Line 60: Line 60:


To summarize, replacing short addresses with long addresses usually works, but the other way round usually fails.
To summarize, replacing short addresses with long addresses usually works, but the other way round usually fails.
== Writing or reusing a probe function ==
If you have a chip with id1 0xc2, id2 0x18, first run
flashrom -V
to get an overview of the probe results for the existing probe functions. There's a good chance you'll find a probe function (or even many of them) that works for you. To automate this, run
flashrom -V|grep "0xc2.*0x18"|sed "s/.*probe/probe/"|sort|uniq
and you get a neat list of probe function names and their results, looking roughly like this:
probe_29f002: id1 0xc2, id2 0x18
probe_29f040b: id1 0xc2, id2 0x18
probe_jedec: id1 0xc2, id2 0x18
probe_stm50flw0x0x: id1 0xc2, id2 0x18
probe_w39v040c: id1 0xc2, id2 0x18
probe_winbond_fwhub: id1 0xc2, id2 0x18
As you can see, there are quite a lot of probe functions which seem to work fine (and that's mostly because of the ignored address bits). probe_jedec is the most-used function in our tree, so if the sequence looks ok, please use that one.

Revision as of 13:35, 20 August 2009

Feel free to cut-n-paste from mails and IRC into this page. Grammar and spelling are not so important.

What numbers do FWH/LPC chips tend to start with?

39/49/50 with 49 being the most common. I've seen 39/49 chips which are parallel but that's ususual. 50 is not very common as model number.

Dirty little secrets why chips are not found although the chipset and the chip are supported

14:10 < carldani> there's a dirty little secret for EEPROMs

14:10 < carldani> actually, two secrets

14:11 < carldani> 1. old parallel flash chips often need a special board enable or the flash chip will ignore any commands (get ID, erase, write)

14:11 < carldani> (that's the case with most boards of PIIX4 or older era, flash chip model names are usually *29*)

14:12 < carldani> 2. modern chipsets usually have more than one flash bus, and some boards even have additional bus translation chips

14:13 < carldani> so for modern boards you have to check the LPC/FWH bus of the chipset, then you check the SPI bus of the chipset (if supported by the chipset and supported by flashrom), then you check the SPI bus of any LPC-to-SPI bus translation chip

14:13 < carldani> on the M2N68, we only probe for LPC chips, but the chip on the board is SPI

14:14 < carldani> that means the SPI chip is either attached to the SPI bus of the chipset (and we don't have a driver for that due to lack of docs)

14:14 < carldani> or it is behind some LPC/SPI translation chip (some of which we support)

14:14 < carldani> the translation test is performed with -p it87spi

14:15 < carldani> as you can see, it's complicated

14:15 < carldani> worst of all, autodetection is basically impossible

Patch submission

The following guidelines are for coreboot, but most of them apply to flashrom as well: http://www.coreboot.org/Development_Guidelines The really important part is about the Signed-off-by procedure.

We try to reuse as much code as possible and create new files only if absolutely needed, so if you find a function somewhere in the tree which already does what you want (even if it is for a totally different chip), please use it. Most chips work fine with probe_jedec even if the command sequence seems to differ at first glance. See also Command set secrets below.

The patch reviews may sound harsh, but please don't get discouraged. We try to merge simple patches after one or two iterations and complicated ones after a maximum of three iterations.

If you introduce new features (not flash chips, but stuff like partial programming, support for new external programmers, voltage handling, etc) please discuss your plans on the list first. That way, we can avoid duplicated work and know about how flashrom internals need to be adjusted and you avoid frustration if there is some disagreement about the design.

Command set secrets

This is only mentioned in very few datasheets, but it applies to most parallel (and some LPC) chips I saw: Upper address bits of commands are ignored if they are not mentioned explicitly. If a datasheet specifies the following sequence:

chip_writeb(0xAA, bios + 0x555);
chip_writeb(0x55, bios + 0x2AA);
chip_writeb(0x90, bios + 0x555);

then it is quite likely the following sequence will work as well

chip_writeb(0xAA, bios + 0x5555);
chip_writeb(0x55, bios + 0x2AAA);
chip_writeb(0x90, bios + 0x5555);

However, if the chip datasheet specifies addresses like 0x5555, you can't shorten them to 0x555.

To summarize, replacing short addresses with long addresses usually works, but the other way round usually fails.

Writing or reusing a probe function

If you have a chip with id1 0xc2, id2 0x18, first run

flashrom -V

to get an overview of the probe results for the existing probe functions. There's a good chance you'll find a probe function (or even many of them) that works for you. To automate this, run

flashrom -V|grep "0xc2.*0x18"|sed "s/.*probe/probe/"|sort|uniq

and you get a neat list of probe function names and their results, looking roughly like this:

probe_29f002: id1 0xc2, id2 0x18
probe_29f040b: id1 0xc2, id2 0x18
probe_jedec: id1 0xc2, id2 0x18
probe_stm50flw0x0x: id1 0xc2, id2 0x18
probe_w39v040c: id1 0xc2, id2 0x18
probe_winbond_fwhub: id1 0xc2, id2 0x18

As you can see, there are quite a lot of probe functions which seem to work fine (and that's mostly because of the ignored address bits). probe_jedec is the most-used function in our tree, so if the sequence looks ok, please use that one.